例句與造句

1. software of forecasting finish rolling temperature for hsm was developed based on the traditional strip temperature dropping model
   摘要在傳統熱連軋精軋機組溫降模型基礎上，開發了帶鋼熱連軋終軋溫度預報軟件。
2. it also simulated the influence and relationship in the transfiguration resisting force, coefficient of he transfiguration resisting force, rolling area, rolling temperature, rolling pressure, loop length, the transition between loop length and loop high
   模擬仿真出了變形抗力、接觸面積、溫度、軋制壓力、活套套量、活套套量與套高轉換等各個模型之間的相互影響。
3. the experimental results show that decreasing rolling temperature is helpful in getting the fine austenite grain size in comparison with the conventional rolling deformation temperature, which is a kind of potential technique for improving the general properties of the workpieces
   實驗結果表明：降低軋制溫度有利于得到較細小的高溫奧氏體晶粒，是一種提高工件綜合性能的新工藝。
4. the influence of the melt transfer temperature, spinning temperature, temperature and speed of quench air, the 1st hot rolls temperature, the 3th hot rolls temperature, drawn ratio on dying property of melt direct spun fdy were discussed
   摘要主要就熔體直接紡fdy生產過程中熔體輸送溫度、紡絲溫度、側吹風溫度、風速、第一對熱輥溫度、第三對熱輥溫度、拉伸倍數等因素對染色性能的影響進行探討。
5. the influence of the melt transfer temperature, spinning temperature, temperature and speed of quench air, the 1st hot rolls temperature, the 3th hot rolls temperature, drawn ratio on dying property of melt direct spun fdy were discussed
   摘要主要就熔體直接紡fdy生產過程中熔體輸送溫度、紡絲溫度、側吹風溫度、風速、第一對熱輥溫度、第三對熱輥溫度、拉伸倍數等因素對染色性能的影響進行探討。
6. It's difficult to find roll temperature in a sentence. 用roll temperature造句挺難的
7. firstly, the distortion of rolled piece and the designing method in the beforehand slit pass and slit pass has been analyzed . secondly, based on the research production of predecessor and research of the author, card system selected some corresponding experience formulas such as roll force, roll moment, roll temperature and roll consume, and established spread model in the beforehand slit pass and slit pass and the distribution model of elongation coefficient . subsequently, card system applied the dynamic programming method with minimum roll consume and optimized its pass system
   本文以圓鋼雙線切分為基本實體模型，著重分析了預切分孔型和切分孔型在軋制過程中的變形特點及相應的孔型設計方法；基于前人的研究成果及作者的探索，選擇了相應的軋制力、軋制力矩、溫度及能耗模型，建立了預切分和切分的寬展及延伸系數的分配模型；應用動態規劃法以能耗最小為目標函數對孔型系統進行了優化設計；利用visualbasic6.0和microsoftaccess數據庫的連接，建立了數據查詢系統，以visualbasic6.0和autocad之間的接口在vb環境下完成了斷面孔型圖的繪制。